Printer Setting Change

This command sets the printer configuration specified by m and n. After receiving this command, the printer is reset to activate the setting. If m or n is out of range, the printer ignores this command but waits for the data until terminator code 0FFH.

ASCII	US DC1 [m n], [m n]… [m n] 0FFH
Hexadecimal	1F 11 [m n], [m n]…[m n] 0FFH
Decimal	31 17 [m n], [m n]…[m n] 0FFH

Values of m, n (Hex)
m	Function	n	Function
10	Interface type	•00 •01 •02	•USB/RS232C •RS232C •USB
11	Baud rate	•00 •01 •02 •03 •04 •05 •06 •07	•115200 bps • 57600 bps • 38400 bps • 19200 bps • 9600 bps • 4800 bps • 2400 bps • 1200 bps
12	Number of data bit	•00 •01	•8 data bits •7 data bits
13	Number of stop bit	•00 •01	•1 stop bits •2 stop bits
14	Parity	•00 •01 •02	•No parity •Even parity •Odd parity
15	Flow control	•00 •01	•Software (XON/XOFF) •Hardware (DTR/DSR)
16	Data reception errors option	•00 •01	•Ignore errors •Print “?”
17	One line buffer	•00 •01 •02 •03	•4K Buffer •One line buffer (128 Bytes) •8K •12K
18	DSR signal option	•00 •01	•Enable DSR signal •Disable DSR signal
19	Printer ID mode	•00 •01 •02	•7158 Native ID •Emulated Printer ID •7167 Native ID
20	Emulation	•00 •01 •02 •03	•7158 Native mode •7156 mode •7150 mode •7167 Mode
21	Default lines per inch	•00 •01 •02	•8.13 lines per inch •7.52 lines per inch •6 lines per inch
22	Carriage return usage	•00 •01	•Ignore CR •Use CR as Print cmd.
23	Asian mode	•00 •01	•Asian mode on •Asian mode off
24	Slip Print Width Option	•00 •01	•82.2 mm (7167 Mode) •120.7 mm (7156/58 Mode)
25	Receipt synchronization	•00 •01	•Synchronization enabled •Synchronization disabled
26	Platen Waiting Time	•00 •01 •02	•No Extra Time •Extra 1 second •Extra 2 seconds
27	PDF417 Print Column	•00 •01	• 9 Columns •14 Columns
28	RS485 Emulation	•00 •01	•4610 Emulation •4R Emulation
29	4610 Emulation	•00 •01	•4610 TI4 •4610 TI9
2A	Landscape Mode	•00 •01	•Page Mode •Line-by-line Mode
30	Print Density	•F1 •F2 •F3 •F4 •F5 •F6 •F7 •F8 •F9 •FA •FB •FC •FD •FE •FF •00 •01 •02 •03 •04 •05 •06 •07 •08 •09 •0A •0B •0C •0D •0E •0F	•-15 •-14 •-13 •-12 •-11 •-10 •-09 •-08 •-07 •-06 •-05 •-04 •-03 •-02 •-01 •00 •+01 •+02 •+03 •+04 •+05 •+06 •+07 •+08 •+09 •+10 •+11 •+12 •+13 •+14 •+15d
31	Paper Low sensor option	•00 •01	•Paper low sensor enable •Paper low sensor disable
32	Paper width	•00 •01	•80 mm •58 mm
33	Knife option	•00 •01	•Enable knife •Disable knife
34	MICR option	•00 •01	•Enable MICR •Diasble MICR
35	Check Flip option	•00 •01	•Enable check flip •Disable check flip
36	Max Power option	•00 •01	•Term Pwr-High •NCR 75W Ext Pwr
37	Color Paper option	•00 •01	•One Color Paper •Two Color Paper
38	MICR dual pass option	•00 •01	•Dual pass disable •Dual pass enable
3E	FONT Type	•00 •01	•Font1, use original font. (all code page) •Font2, use increased font size for CP473 and CP858.
3F	Char 48 Column Print	•00 •01	•OFF •ON
40	Default code page	•00 •01 •02 •03 •04 •05 •06	•437 •850 •852 •858 •860 •862 •863
40	Default code page	•07 •08 •09 •0A •0B •0C •0D •0E •0F	•864 •865 •866 •874 •1252 •Katakana •932 (or 936, 949, 950) •Hungary •1256
41–44	Reserved
45	Set paper detection	•00 •01	•Enable •Disable
50	EEPROM default setting	00	EEPROM default setting
57	ECO function disable / enable in Lean utility	•00 •01	•Disable •Enable
58	Space Character Line in Eco utility	•00 •01	•Character •Line Feed
60	Thermal Printing Mode	•00 •01 •02 •03	•Single Sided Mode •Double Sided Mode with Single Side command •Double Sided Mode with Double Side Command •Double Sided Mode with Pre-Defined data
61	Upside Down Printing for Double Side	•00 •01 •02 •03	•Front: Normal, Back: Normal •Front: Upside down, Back Normal •Front: Normal, Back: Upside Down •Front: Upside Down, Back Upside Down
62	Swap Front Side and Back Side	•00 •01	•Not Swap •Swap Front and Back side
63	Pre-Defined Bottom/Top Message	•00 •01 •02 •03	•No Message •Bottom Message on Front •Top Message on Back •Both Bottom Message on Front and Top Message on Back
64	Minimum Receipt Length	•00 •01-FF	•No Min. Receipt Length •Minimum receipt length (inches)
65	Minimum Receipt Length (Integer after dividing Min. Receipt Length by 256)	00-FF (max value tbd)	Length in dot rows for Minimum receipt length
66	Reprint when Error Occurs	•00 •01	•Resume printing from last error line •Reprint the error page
67	Reprint Message	•00 •01	•No Message •Reprint Message
68	USB Interface Type (Refer Notes)	•00 •01 •02	•Not use (Reserve for EpiC) •NHPI •PRTR
7F	Compatibility Barcode Length	•00 •01	•Disable •Enable
80	Receipt Print Mode (Speed Reduction in Eco utility)	•00 •01	•High Speed Print •High Quality Print
81	Power-On Thermal Head Failure Detection Mode	•00 •01	•OFF •ON
82	Standby mode (Enable Stand-by Mode in Eco utility)	•00 •01	•Disabled •Enabled
83	Shift time to Power-off (enable Off Mode in Eco utility)	•00 •01 •02 •03 •04 •05	•Disabled •60min •120min •180min •240min •300min

Notes

This command changes configuration setting in EEPROM. If same value that is set in EEPROM is set, this command doesn’t write to EEPROM.

Restart the terminal after setting the Landscape Mode, RS485 Emulation and 4610 Emulation parameters. These parameters are supported only in RS485 model.

USB Interface Type depends on firmware version and is set as follows.

Command Value	ION USB version	Non ION USB version
00 (EPiC) (If used)	Ignore	01 (NHPI)
01 (NHPI)	Ignore	01 (NHPI)
02 (PRTR)	Ignore	02 (PRTR)

Default value of EEPROM:

ION USB version : 0x00 (EPiC)

Non ION USB version : 0x01 (NHPI)