Error Codes
TseFlash.com supports the following return error codes.
| Error Code | Definition |
|---|---|
| 0 | Download successfully completed or Get firmware version process successfully completed |
| 101 | Cannot erase a sector |
| 102 | Cannot select a sector |
| 103 | Timeout while sending data block |
| 104 | Cannot acknowledge printer Note
Please check the interface settings. |
| 105 | Different CRC detected |
| 106 | Cannot recalculate CRC |
| 107 | Unable to open file |
| 108 | Insufficient memory for data buffer |
| 109 | Communication interface busy |
| 110 | Cannot switch printer to flash download mode |
| 111 | Cannot reset printer |
| 112 | Unrecognized download type set |
| 113 | Illegal COM port set |
| 114 | Illegal parity set |
| 115 | Illegal baud rate set |
| 116 | Illegal stop bit set |
| 117 | Unable to get serial port handle |
| 118 | Unable to set serial port properties |
| 119 | Too few / many command line parameters |
| 120 | Invalid binary data file |
| 121 | /? Detected |
| 122 | Unable to update window text |
| 123 | Unable to show progress bar |
| 124 | Data file error |
| 125 | Insufficient memory |
| 126 | Unrecognized product model set |
| 127 | Application was terminated by Exit button |
| 128 | Unable to get printer actual baud rate |
| 129 | Mismatch between download type and file selected |
| 130 | Unable to get printer model number Note
Please check the printer connection. |
| 131 | Download was cancelled due to the download file not support for this printer |
| 132 | Invalid parameter for skipping/non-skipping model number |
| 133 | Invalid parameter for printing/non-printing printer |
| 134 | Initial/Boot file extension mismatch |
| 135 | Initial/Boot file length exceeded 32KB |
| 136 | Initial/Boot file information incorrect |
| 137 | Error setting Park II download mode |
| 138 | No printer is detected through USB Interface |
| 139 | Can not reconnect as CPMI Device |
| 140 | Can not reconnect through USB interface |
| 141 | The Printer model does not match the selected model |
| 142 | No printer is detected through Parallel Interface |
| 143 | No printer is detected through Communication Port Note
The baud rate setting could also be incorrect. |
| 144 | Clear the download area fail |
| 145 | Download Fail |
| 146 | Upload file fail |
| 147 | Can not Open FTP server |
| 148 | Can not connect to FTP server |
| 149 | Select Sector acknowledge fail |
| 150 | Insufficient file size |
| 151 | CRC acknowledge fail |
| 152 | CRC is not correct |
| 154 | Can not get printer IP address |
| 155 | Can not get MAC Address |
| 156 | Socket Open Failed |
| 157 | Socket Data Sending Failed |
| 158 | Cannot Get Printer Firmware Version |
| 200 | Invalid parameter for Model Number |
| 201 | Invalid parameter for Download Type |
| 202 | Invalid parameter for Interface Type |
| 203 | Invalid parameter for IP Address |
| 204 | Invalid parameter for Baud Rate |
| 205 | Invalid parameter for Parity |
| 206 | Invalid parameter for Stop Bits |
| 207 | Invalid File Name |
| 208 | Invalid paramater for Check Model option |
| 209 | Invalid parameter for Print option |
| 210 | No enough arguments |
| 211 | The selected model is not correct |
| 212 | Parameter is error, please check the Print option, Status option or Errortimeout option! |
| 401 | Cannot Swap IBM USB Firmware |
| 402 | IBM USB Swap Memory Command Rejected |
| 501 | CPMI Device not found |
| 503 | Error to get PRTR Handle |
| 504 | Please Make Sure Printer is in Online Mode |
| 505 | Illegal Parameter |
| 506 | File Size Mismatch |
| 507 | Wrong Firmware File |
| 508 | Fail writing into flash memory |
| 509 | CRC mismatch |
| 510 | Unable to scan device |
| 511 | Unable to open device |
| 259 | Terminated after reach ErrorTimeOut parameter |
