Advanced Menu

Boot Configuration

Quick Boot

[Disabled]

Boot Menu

[Enabled]

High Resolution Graphics

[Enabled]

Diagnostic Splash Screen

[Disabled]

Diagnostic Summary Screen

[Disabled]

BIOS Level USB

[Enabled]

USB Legacy

[Enabled]

Console Redirection

[Disabled]

UEFI Boot

[Enabled]

Legacy Boot

[Enabled]

Load OPROM

[On Demand]

ACPI Configuration

Deep Standby

[Disabled]

Processor Configuration

Single Processor Mode

[Disabled]

Intel (R) HT Technology

[Enabled]

Enable XD

[Enabled]

Machine Check

[Enabled]

Fast Strings

[Enabled]

Processor Power Management

[Disabled]

Thermal Configuration

. TM1

[Enabled]

. TM2

[Enabled]

. DTS

[Enabled]

. Thermal Offset

[Disabled]

. Active Trip Point Hi Fan

[71 C]

. Active Trip Point Lo Fan

[55 C]

. Passive Trip Point

[95 C]

. Passive TC1 Value

[ 1]

. Passive TC2 Value

[ 5]

. Passive TSP Value

[10]

. Critical Trip Point

[POR]

P-States (GV3)

[Enabled]

Boot Performance Mode

[Max Performance]

ACPI 3.0 T-States

[Enabled]

C-States

[Disabled]

Serial ATA (SATA)

SATA Device

[Enabled]

SATA Controller Mode

[AHCI]

Device 0 (Port 0)

[Not Installed]

Device 1 (Port 1)

[INTEL SSDSA2CT - 40]

► SATA Port 0 Configuration

. Port Location

[Internal]

. Hot Plug

[Enabled]

. Interlock Switch

[Disabled]

. Port Multiplier

[Disabled]

► SATA Port 1 Configuration

. Port Location

[Internal]

. Hot Plug

[Enabled]

. Interlock Switch

[Disabled]

. Port Multiplier

[Disabled]

North Bridge Configuration

Clock Spread Spectrum

[Min Spread Spectrum]

Primary Display Selection

[IGD]

DMI ASPM

[Enabled]

► IGD Configuration

 

. IGD - Boot Type

[VBIOS Default]

. IGD - Panel Scaling

[Auto]

South Bridge Configuration

SMBUS Device

[Enabled]

Enable Serial IRQ

[Enabled]

Serial IRQ Mode

[Continuous]

CLKRUN# Logic

[Enabled]

ICH Internal LAN

[Enabled]

Wake on LAN

[Enabled]

LAN OPROM Selection

[Enabled]

HPET Support

[Enabled]

HPET Memory Map BAR

[F#D00000]

State After G3

[Last State]

► SB Azalia Configuration

 

. Azalia

[Enabled]

. Azalia PME Enabled

[Enabled]

. Azalia Vci Enabled

[Enabled]

► SB USB Configuration

. UHCI Controller #1

[Enabled]

. UHCI Controller #2

[Enabled]

. UHCI Controller #3

[Enabled]

. UHCI Controller #4

[Enabled]

. EHCI

[Enabled]

► SB PCI Express Configuration

. ► PCI Express Port 1/2 Config

 

. . . PCI Express Root Port 1

[Enabled]

. . . IO APIC Support

[Disabled]

. . . Automatic ASPM

[Auto]

. . . PME Interrupt

[Enabled]

. . . Hot Plug SCI

[Disabled]

. . . Extended Synch Enable

[Disabled]

. . . URR

[Disabled]

. . . FER

[Disabled]

. . . NFER

[Disabled]

. . . CER

[Disabled]

. . . SEFE

[Disabled]

. . . SENFE

[Disabled]

. . . SECE

[Disabled]

. ► PCI Express Root Port 3

[Disabled]

. ► PCI Express Root Port 4

[Disabled]

LPC Configuration

Onboard UART1

[Enabled]

CPU FAN SPEED

[60% OF MAX]

SMBIOS Event Log

Event Log Validity

Valid

Event Log Capacity

Space Available

Event Log

[Enabled]

View SMBIOS event log

[Enter]

Mark SMBIOS events as read

[Enter]

Clears SMBIOS events

[Enter]

Intel Fast Flash Standby

iFFS Support

[Disabled]

Hardware Health Monitoring

Typical (Acceptable Range)

CPU Core 1 Temperature

[56°C] (less than 95°C)

CPU Core 2 Temperature

[56°C] (less than 95°C)

CPU Core 3 Temperature

[60°C] (less than 95°C)

CPU Core 4 Temperature

[60°C] (less than 95°C)

System Temperature

[46°C] (less than 70°C)

DIMM Temperature

[43°C] (less than 70°C)

CPU Fan Speed

[ N/A]

System Fan Speed

[ N/A]

V CPU Core

[ 1.168 V] (1.00 - 1.30)

V 1.05S

[ 1.040 V] (0.90 - 1.20)

V 3.3S

[ 3.312 V] (3.05 - 3.55)

V 5S

[ 4.972 V] (4.60 - 5.40)

V 12S

[12.096 V] (11.20 - 12.80)

V 5A

[ 4.921 V] (4.60 - 5.40)

V Batt

[ 3.264 V] (3.0 - 3.5)